Groups and families
Two people side by side interrupt the beam only once. The busier the door, the more is missing from the figure.
The beam on the door frame is the simplest people counter, the camera above the entrance the more versatile one. How both count, where an infrared beam people counter is all you need, and when a camera is the better beam counter alternative.
A beam counter counts how often a light beam across the door is interrupted. It is cheap, quick to fit and often enough for a narrow door with little traffic. Vicodis counts with an Axis camera that detects people in the image and knows which way they walk. If you only want to know whether a day was busy or quiet, the beam will do. If you need in and out separately, the current occupancy or a wide door, it is the camera.
A door beam counter consists of a transmitter and a receiver or reflector that face each other on the door frame, usually at about hip height. The transmitter sends an invisible beam across the doorway. When someone walks through, the beam breaks for a moment and the device adds one. Most devices use infrared light and run on batteries, so no cable to the door is needed.
A single beam knows no direction. It counts every interruption, whether someone arrives or leaves, which is why many operators divide the daily figure by two. Direction detection needs two beams close together: the order in which they are interrupted reveals the walking direction.
The camera works differently. It sits above the entrance, looks down at the doorway at an angle and detects each person as a separate object. A person is counted when they cross a line in the image that you have drawn yourself. How the other methods work, from thermal sensors to 3D sensors, is explained in the guide to people counting.
| Vicodis | Typical beam counter | |
|---|---|---|
| Sensor | Axis camera with an AI processor above the entrance | Transmitter and receiver on the door frame |
| What is counted | Every detected person crossing the line | Every interruption of the beam |
| Direction | In and out separately | Only with two beams |
| People side by side | Detected one by one | Interrupt the beam together |
| Wide entrances | One camera covers the doorway | Limited by the range of the beam |
| Current occupancy | Live figure with traffic light and limit | Usually not provided |
| Reporting | Dashboard, calendar, CSV and PDF from the camera | Counter on the device or the supplier's software |
| Power | Over the network cable | Mostly battery |
The table describes the usual design. There are beam counters with a radio link and their own reporting, and there are entrances where no camera may be installed. Which Axis models are suitable for counting and how high they need to be mounted is covered under people counting cameras.
Two people side by side interrupt the beam only once. The busier the door, the more is missing from the figure.
Someone who waits in the doorway, swings a bag or pushes a pram can trigger several interruptions or cover the beam.
The number of people present depends on entries and exits both being right. Small errors in both directions add up over hours.
Wide entrances, arcades and outdoor gates often have no frame on which transmitter and receiver can face each other.
For a single shop door where only the trend matters, a camera is more than you need. What you get when requirements grow is described under the Vicodis Visitor Counter.
Only with two beams one behind the other. A single beam counts every interruption the same way, whether someone arrives or leaves. Devices with two beams derive the direction from the order of interruption. That works as long as people pass one at a time and briskly, and becomes uncertain when someone stops or turns round.
Because it counts interruptions, not people. When two people walk through the door side by side or close behind each other, the beam stays covered and is counted only once. A camera above the entrance sees the doorway from above and detects each person as a separate object before they cross the counting line.
With care. The camera counts people and separates the directions, while the beam counted interruptions. The new figures are therefore often higher although no more visitors are coming. Run both devices in parallel for a few weeks. Then you know the ratio between them and can put earlier years into context.
That depends on what you do with the figure. For a rough trend a beam is enough. If you want to see peak hours, set visitors against till receipts or keep to a maximum number, the camera delivers the values you need. If a suitable Axis camera is already at the entrance, a licence is all it takes.
This page describes the typical design of beam counters for people counting as a product category. Individual products differ. Check the details with the supplier you are considering.
Tell us your camera model or your project. We check compatibility and come back with a concrete proposal.